From how well we get enough sleep, in many ways, the mood depends on how well we work. And he is very upset, having given the predetermined time to sleep, to feel broken and lethargic in the morning. This happens if the mattress is selected incorrectly. Perhaps it is worth discussing the issue of how to choose a mattress for a bed – so that it is so comfortable and useful for the body.
We choose the size of the mattress under the bed
Before buying a mattress, you need to accurately measure the inside perimeter of your bed. Remove the old mattress and then take the tape out of place. It can be tempting to measure a pulled mattress – it’s easier. But this is not necessary, as its dimensions change over time due to the inevitable deformation. By the way, when you buy a new bed, you do not need to make measurements – all sizes must be indicated on the product passport.
It happens that the measurements give atypical results. For example, instead of 80 cm, the width is 79 or 83 cm. We must remember that a deviation of up to 1 cm is perfectly acceptable (with a bed size 79 to 201 cm, boldly buy a standard mattress 80 to 200 cm). But if the difference is 2 cm or more, you will have to buy the product to order. Otherwise, the mattress will either not fit in the opening of the bed or will hang inside it. In the latter case, the cover wears out quickly, which often needs to be changed.
When buying an American mattress for a bed made in Europe (or vice versa), be prepared for the fact that it will be quite difficult. European length measures are based on centimeters, unlike American ones, where the starting point is one inch. Get one of the standard American-size bedding – 60 by 80 inches. If you convert inches to centimeters, we get numbers in fractions. Width 152.4 cm and length 203 cm. The standard two-meter length of a European product is initially smaller and the width is very different. Thus, a 160 cm wide mattress will be very large and the next size on the ruler is 140 cm. This is very small.
You can use one of three options:
# 1.It is easier to buy a bed and a mattress from one manufacturer. They will definitely fit together perfectly.
# 2. If it is not possible to buy products under the same brand, then it is worth choosing a mattress made in the same country in which the bed is made.
# 3.You can make a mattress in size by contacting one of the manufacturers. Domestic factories willingly provide such a service (for a fee, of course).
By the way, many well-known European factories that produce expensive and reputable products treat their customers with great care. Each model is presented in all sizes (European and American). In addition, the price of the products is usually stable. After all, this is a premium class, and so very expensive.
Mattress with spring or without opening
There are two main types of layers – with spring blocks inside and none at all. In turn, the springs can also have a different design, based on which they are called dependent or independent.
Mattresses in springs
# 1.Suspended spring blocks.
Let’s start with a description of the dependent spring blocks – this is what they say because when you push on one of the springs, everyone else also comes into motion. This option is cheaper, but has a minus. After a while, such mattresses are very stretched in the middle – a kind of hammock is obtained. And if two sleep in such a bed, then the lightest spouse will inevitably slip into the one who is heavier. Therefore, it is best to leave the dependent spring structures for supply or other short-term use.
The device of the mattress with a dependent spring unit: 1 – mattress wallpaper. 2 – spring block of dependent springs. 3 – felt layer. 4 – polyurethane foam (foam rubber). 5 – the perimeter of polyurethane foam.
Appearance of the Bonnel spring block with dependent springs.
Mattress based on a dependent spring unit.
# 2.Independent blocks are convenient, but expensive.
Here, each spring, which works separately from the others, is enclosed in a case made of a special fabric – spunbond. A similar layer serves for a long time, and no relaxation is observed. This is exactly the price it has is quite high.
And what spring mattress to choose for the bed so that it lasts a long time and has a reasonable price? Surely many have such a desire. Well, look at the models with TFK spring block – they are the most economical. There are 250 springs per square meter of surface in such a block. The most expensive design S 1000 has such springs 500 and S 2000 – 2 times more.
In proportion to the price and the number of springs, the orthopedic effect of the mattress also increases. It makes sense to buy such products for a bed in which you sleep constantly.
The mattress device with an independent spring unit: 1 – coconut coconut; 2 – latex layer. 3 – spring in the case; 4 – mattress cover, 5 – the perimeter of the mattress (usually made of polyurethane foam). 6 – independent spring unit. 7 – coconut.
Each opening is sewn to the cover, the result is ribbons from which spring blocks are assembled independently.
Mattress based on an independent spring unit.
Mattresses without springs
As the name implies, these are mattresses without springs; they have a simpler device.
Stainless steel mattress device: 1 – mattress cover; 2 – a layer of coconut coconut; 3 – latex layer.
These products differ in the type of filler contained in them. As mentioned above, the more expensive models, filled with natural materials, are valued more. This is latex with elasticity, resilience and anti-allergen, as well as coconut flakes (coconut), which can give the product rigidity.
Springless mattress with natural filling of latex and coconut.
However, these cheap types of mattress pads that are filled with artificial materials are quite popular. This, in particular, polyurethane foam (foam), artificial latex, as well as holofiber. Of course, they will serve slightly less than products with natural ingredients inside. But their price is much lower.
Springless mattress made of polyurethane foam (foam rubber) and coconut.
It is determined by the stiffness of the mattress
If you sleep too hard on a mattress, your body weight may be unevenly distributed. Particularly unpleasant sensations in this case occur in the area of the shoulders and hips. After all, the heaviest loads fall on these zones. And in the morning, you wake up in such a mattress, you feel a little hit. However, when deciding which bedding mattress to buy, you should not go for the other extreme. The very soft product will also not give full sleep – the muscles and ligaments will be too tight.
If a person is thin and light, then a soft mattress will not hurt him – people who weigh less than 55 kg will sleep perfectly in it. For those who have an average weight – from 55 to 90 kg – you can buy a mattress with moderate rigidity. However, “heavyweights” of 90 kilograms or more should turn to more rigid products. In this case, do not be afraid of discomfort during sleep – everything will be fine. It will be comfortable to sit on the bed, as the edges of the mattress will probably not bend.
1. Latex. 2. Coconut. In the photo you can see a double-sided mattress, both sides of which have different stiffness. This is achieved by the fact that the last layer on the one hand is coconut, and on the other a layer of latex. Mattresses with different stiffnesses are both without springs and with springs (picture). They can be useful to those who can not determine exactly the rigidity needed.
What crews is best to use a mattress
It is the filler, located above the spring and below it, that determines the stiffness and elasticity characteristics of the mattress. The best are the “breathable” natural fillers, which also serve for a long time. However, they have a minus – a fairly high price. One thing can be said: for those whose weight has exceeded one centner, it is still worth choosing a natural filling that is extremely wear-resistant.
Stiffness often depends on the thickness and type of filler. One of the natural materials commonly used in mattresses is coconut. It is often used to give the mattress a certain rigidity.
IF THE THICKNESS OF THIS MATERIAL IS ONLY ONE CENTIMETER, THEN WE WILL HAVE THE PRODUCT WITH MEDIUM RIGIDITY. BUT THREE CENTIMETERS OF COCONUT WILL GIVE A VERY HARD LAYER.
ANOTHER POPULAR NATURAL FILLER IS LATEX. LATEX, UNLIKE COCONUT, SOFTENS THE SURFACE AND MAKES IT MORE FLEXIBLE AND COMFORTABLE.
In addition to natural, many artificial fillers are also used. One of the most popular is polyurethane foam, commonly called rubber foam. In addition, premium mattresses and cheap budget products are made from it.
HOWEVER, IN ANY CASE, FOAM RUBBER IS THE CHEAPEST OF THE FILLERS. IT CAN HAVE NOT ONLY DIFFERENT THICKNESS AND DENSITY, BUT ALSO CRAFTSMANSHIP.
Studying what mattresses for beds are, let’s stay in front of another filler, which is considered one of the most elite – this is holofiber. Despite its artificial origin, it is by no means inferior (and sometimes superior) to natural fillers. The homogeneous structure of holofiber is created due to the large number of small coils.
THE PRODUCTS FROM IT RETAIN HEAT PERFECTLY, ALLOW AIR TO PASS THROUGH AND DO NOT ABSORB MOISTURE AND ODORS. THEY DO NOT LOSE THEIR ATTRACTIVE APPEARANCE FOR A LONG TIME, DO NOT DEFORM. THERE ARE ALL THE BEST PROPERTIES OF MATTRESSES, BOTH SPRING AND SPRING.
The mattress is covered by wallpaper – we choose the wallpaper
When we arrive at the mattress store, first pay attention to their appearance. Here the manufacturers try to put their products in beautiful covers that are pleasant to the touch. In addition, it is important that the wallpaper is strong enough to withstand years of use. The designs and textures of mattress covers offered today shine with variety. Some may turn to the wrong side, having a different color.
For sewing covers use strong natural (cotton, linen) or artificial (polypropylene, polyester) fabrics. Special impregnations increase strength and elasticity. There are anti-allergenic impregnations as well as those that protect against dust. This variety increases the choice of mattress for the bed. The final decision should be based on your requests.
Features of choosing a mattress for a double bed
Compared to single and one and a half layers, double products have to adapt to higher loads. After all, sleeping on them is not one person, but two. So here you need sufficient elasticity, rigidity and wear resistance.
It is especially difficult when the weight of the spouses holding the bed is different. We give an example. The wife, for example, is small and slender and weighs only 48 kg. And her husband, strong, tall and well-groomed, weighs almost twice as much – 90 kilos. It turns out that when choosing a mattress, someone alone will always be uncomfortable sleeping. For example, buying a soft product can make a fragile woman’s dream comfortable. Well, a hard or semi-rigid mattress is only suitable for her husband and will not be very comfortable.
However, there is an opportunity to rectify this situation. Indeed, a wide bed allows you to place two narrower ones instead of one large mattress.
This is more preferred:
- Some isolation will allow you not to wake up your “half”, to fly and return to a dream.
- You can buy two layers of different stiffness, each of which will be ideally suited to the skin and the weight of the person sleeping on it.
- And let the small gap between the layers not bother you – it is easy to eliminate. Just buy a thin wide mattress cover, which is a rug without springs. It will combine the two boxes into one.
However, there are families where they do not want to think about separate mattresses, preferring to sleep side by side, very close to each other. Good spouses have a right to this. They can buy a model with two sides that have different rigidity. Let one of them be moderately hard, and vice versa – quite soft. First you have to experiment by turning the mattress. Then we can conclude from which side it is better for both spouses to sleep. We believe that the above tips will help you understand how to choose the right mattress for the bed.more info to visit :http://thdailymagazine.com/